AIWA

              Encender el TV,Abrir el control remoto y buscar las teclas que no tienen acceso para el usuariopresionar una de ellas y luego DISPLAYaparecerá en la pantalla el menú servicio.Con canal mas-menos seleccionar el ítem.VOLUMEN mas-menos y DISPLAY muestra los datos a ajustar.Para salir presionar DISPLAY y la otra tecla oculta en el control remoto,aparecerán los caracteres INITIAL por unos segundos y el tv se apagará

                                                       BEKO

-Probar con la secuencia Menu y el codigo 9301. o  -Probar tambien Menu-Idioma y el codigo 9301.

                                                              GRUNDIG

     Debereis de probar con estos codigos       V+ mas V- mas PR - mas PR +,,,,,8500,,,,,7038,,,,,4934

                                                                   JVC

Con el televisor conectado presionar:  DISPLAY y  VIDEO STATUS en el mando a distancia.

En otros modelos:

 Presionar SLEEP TIMER en el mando a distancia y ajustar el  SLEEP TIMER a 0 minutos.En unos momentos saldra en pantalla la informacion del SLEEP TIMER entonces presionar DISPLAY y VIDEO STATUS] y despues SERVICE MENU.

Para salir del modo de servicio pulsar exit en el mando a distancia.

                                                                    LG

En la seccion LG publico varias formas,por lo que tendreis que probar con ellos. 

Con el TVC conectado,presionamos a la vez las dos tecla de menu,una esta en el tvc y otra en el mando,con las teclas channel Up y Down,seleccionamos el ajuste a realizar,y con las teclas volumen Up y Down,le damos los valores deseados o recomendados por el fabricante.

Simultaneamente pulsar las teclas OK en el mando y el panel del TV.

Desde el control remoto, use la siguiente secuencia 7, 3, 9, 2 ENTER, POWER. Luego SETUP+/-

Encender el tv.pulsar la tecla de menu del panel frontal del tvc y a su vez pulsar la tecla menu del control remoto, y entraras en le modo servicio.Para navegar por el modo servicio usa las teclas CHANNEL UP/DOWN.Para cambiar los datos usa las teclas VOLUMEN UP/DOWN.

Desde el control remoto, presionar la siguiente secuencias de teclas,( 7 - 3 - 9 - 2 - ENTER - POWER ) luego SETUP +/-
OTROS.-Encender el TV, pulsar "menú" en el TV y al mismo tiempo "menu" del mando a distancia. Presiona canal + ó - para selecionar los ítems y volumen + ó - para cambiar los valores.

                                                                 DAEWOO

        Con el televisor funcionando pulsas las teclas de mando a distacia    1 - mute - recall - mute,si no dispones de la tecla recall tu mando a distancia,entonces utiliza la tecla Display.En algunos modelos no incorporan la tecla recall entonces deberá hacerse la secuencia con display  <1 - mute - diplay - mute>
 

Con el TV apagado, presionar en el control remoto, la siguiente secuencia: DISPLAY,MENU,3,8,POWER, el equipo encendera en modo de servicio. Ingresar a la opcion "Adjustment". Para salir y guardar cambios apagar el equipo. 

                                                    FIRST LINE

Desde el control remoto, presionar MENU ingresar a INSTALAR, introducir la secuencia 4, 7, 2, 5. Para seleccionar los ítem presionar CANAL +/-, para ajustar el valor presionar VOL +/-. Para guardar los cambios oprimir el botón rojo. Para salir oprimir TV.

En el TV Presionar el botón VOL- , y en el control remoto la secuencia PROG, "-", TV. Para seleccionar los ítem presionar CANAL +/-, para ajustar el valor presionar VOL +/-. Para guardar los cambios oprimir el botón rojo. Para salir oprimir TV.

                                                                               HITACHI

       Presionar la tecla "menu" y al mismo tiempo presionar "power".mantenerlos pulsados unos 3 segundos para ajustar los ítems de sonido.Para ajustes de imagen mantener más de 5 segundos.Para poder modificar los valores se debe colocar D030 para los de video y D020 para los de audio.

                                                              KNEISSEL

1º Encender tv y pulsar tecla central de las 5 que tiene el aparato , mantenerla pulsada.
2ºApagar de int. general y volverlo a encender,entonces apretar tecla on/off de M/D.
3º Con teclas circulares de M/D superior e inferior se ponen los ITEM,con derecha e izquierda se ajustan.
4º Los ajustes se memorizan presionando la tecla M amarilla de M/D.                                                                                  

                                                 MITSUBISHI

-Existen varios codigos para los televisores de esta marca dependiendo del modelo,aqui teneis alguno de ellos,debereis de probar

 Pulsar Menu y despues 1257---------   Pulsar menu y despues 1259

Pulsar Menu y despues 1370----------  Pulsar Menu y despues2356
Pulsar Menu y despues 2357----------  Pulsar Menu y despues 2358
Pulsar Menu y despues 2359

Pulsar Menu y despues 8257

-Con las teclas de video y audio seleccionamos el ajuste que queremos ajustar,y con + o - ajustamos.Para memorizar tecleamos Enter y despues pulsamos en el menu de pantalla salir del modo de servicio8exit service mode)

-Desbloqueo de Mitsubishi.Cuando en pantalla aparece "TV Locked", deberemos presionar en el mando a distancia a la misma vez las teclas, simultáneamente las teclas   QV (Quick View) y 9. Luego entrar a MENU, buscar la opción: Parental Lock  (control de padres),una vez que nos pida la contraseña,volvemos a presionar de nuevo a la misma vez las teclas: QV y 9 y el tvc estara desbloqueado. El código de fabrica es: 0000

                                                                NOKIA

 El Modo de Servicio para el televisor Nokia 21"  Mod: 5575 NIC tubo Black Pla y similares es el siguiente                                                                                 

Pulsar la teclas en el mando a distancia de I(Informacion) M(memoria) y P(tecla de programa)

 

Desde el control remoto presionar en secuencia los siguientes botones: -/-- , MENU, TV.

                                                                                                          PHILIPS

Este modo de servicio para el televisor philips,lo he recogido de foros de lengua inglesa,por eso esta en Ingles.

md1.x Service mode
• To get into service mode short circuit 1s42 and 1s43
• By pressing simultaneously on the keys MENU and - on the TV itself you get into the maintenance menu (SAM).

Service mode 24PW6321/01
ER 0 0 0 0 0 0 0 0 0

E2 Y AX 12 RD 34
U0 N VP 38 GD 28
LL Y VA 00 BD 19
NI Y VL 38 HD 36
TT Y VS 35 HW 40
ET N HP 12
BR Y HG 00
HT 31

Service mode 25PT5121/39

ER 0 0 0 0 0 0 0 0 0

E2 Y AX 13 RD 28
U0 N VP 27 GD 32
LL Y VA 18 BD 40
NI Y VL 31 HD 38
TT Y VS 31 HW 24
ET N HP 36
HG 31

The top line list the last detected errors.
The left row are the options, the two right rows are the geometry settings.
The options are:

E2: 2nd peri
U0: Only UHF
LL: System
NI: NICAM
TT: Teletext France
ET: Teletext Easte

-Cortocircuitar en el tvc los pines M31 y M32,despues debemos de encender el tvc y a realizar los ajustes deseados.En otras versiones de Philips se puentean los puntos M24 y M25 y por supuesto se enciende el tvc.

-Otra variante de Philips es tirar a masa la patilla N° 1 de la memoria Epron,despues de entrar,para memorizar los ajustes y salir,apagar el aparato con el mando a distancia y despues desconectarlo de la red.

-Estando el tvc funcionando,presionar con el mando a distancia las teclas 062596 y Menu,una vez realizado esto,te saldra la letra S,vuelve a presionar Menu y te saldran los ajustes que quieres realizar,con canal + y - seleccionas y con volumen + y - ajustas,para memorizar y salir,pulsar Power.

Desbloqueo del modo Hotel.Para salir del Modo Hotel, buscar el programa 38 y pulsar VOL- y STORE durante varios segundos.

                                                                    PANASONIC

Panasonic tx-28ld2f chasis euro-2

1.Conectas el TV
2.Poner en corto temporal el punto de prueba (FA2) y el tv se activara en modo de cambio y las teclas volumen arriba y abajo se ajustan rapidamente
3.Oprime al mismo tiempo las teclas del panel del tv ACTION Y VOLUMEN ARRIBA PARA ACTIVAR EL MODO DE SERVICIO

  El siguiente modo de servicio lo he sacado de una de las Web de DoubtElectronics,por lo que no estoy completamente seguro de que sea la forma correcta de entrar,pero si no lo sabemos por intentarlo y comprobar si es valido o no es valido,no perdemos nada,os pongo la url original,por si quereis comprobarlo por Vds mismos.la direccio es:            http://www.calanan.com/panasonic/   

Para los televisores Panasonic hay dos formas de entrar en el modo de Servicio.FORMA REMOTA---OTRAS FORMAS.

Forma Remota:A)Con el televisor conectado y con el icono en Setup poner antena en Cable B)Seguidamente con el icono en Timer,poner sleeptimer en 30 c)Salir del menu y ajustar el canal 124,poner el volumen a 0,presionar volumen Down(VD)en el panel frontal y aparecera CHK en rojo,en la parte superior izquierda de la pantalla,ahora presionas Action y VD en el panel de control y ya estas en el service mode.

Otra Forma:Cortocircuitar el punto de prueba FA1 a FA2,en la chasis TP pin 8 a pin 3,nos aparecera CHK en amarillo en la parte superior izquierda,seguidamente presionar Action y VD en el panel de contro y CHK cambiara de color a rojo,y ya estamos en el Service Mode

Una vez dentro del menu de servicio,tenemos 5 submenus que son:

     'B' VCJ Sub Adjustment      'C' W.B. Adjustments    'D' Pincushion Adjustments   'S' Options Adjustments

                                                 CHK' Normal use of VU/VU and CU/CD buttons (Este menu no puede ser ajustado) 

                                                             SANSUNG

Nota:Para conocer el tipo de chasis que es el televisor,este tendremos que comprobarlo,mirando el chasis por debajo,y lo tenemos junto al Flyback

-con el tvc desconectado,presionamos las teclas en el mando a distancia de Mute182 y Power,el televisor se conectaa en el Service mode y en la pantalla son saldra GAMMA GAIN 1,usar los botones de Mute y Menu para mover los valores arriba y abajo,y los de volumen+ y volumen - para realizar los cambios para memorizar presionar la tecla ADD y no la incorpora el TVC presione power.

-Con el televisor en Stand-By presionar en el mando a distancia las teclas MUTE 1 8 2 POWER y saldra en pantalla el menu de fabrica.

-Con el TV en stand-by pulsar  las teclas siguientes con el mando a distancia: Display,Menu,Mute y Power. Con CH +/- se selecciona el valor a ajustar,y con VOL+/- se ajustan los valores.

-Con el TV en Stand-By pulsar la tecla Display----,p.std----mute----power  este modo es para los chasis S15

                                                               SHARP

-En la parte trasera del tvc,los modelos que llevan como una especie de conector con pines,hay que puentear los pines 3 y 6,despues de este debemos pulsar en el mando a distancia mode,y ajustar los valores que queramos con el mas y menos.

-Desconectar el TV de la red,con las teclas CANAL+ y VOL+,pulsadas simultaneamente conecte el TV.Para seleccionar los valores a ajustar Canal + y -.para ajustar con volumen + y -,y para memorizar pulsar Power y despues desconectar el tvc de la red

MODO DE SERVICIO PARA LA  SERIE G.1 - Antes de todo,ahi que realizar un Reset con el mando a distancia para  que los ajustes esten en modo normal.

2 - Destapar el TV, y puentear las puntas de prueba  TP2001 y TP2002, que estan al lado del IC2001. Para entrar en el Modo de Servicio.

3 - Una vez en Modo de Servicio, pulse Canal arriba o abajo con el mando a distancia o tvc.Saldra en pantalla una "S" con un número que varia de 0 a 33. Así puede seleccionar el Item que quiera ajustar.

4 - Seleccionado el Item, con Volume arriba o abajo aparece "D" con un número en la esquina inferior derecha. - Para salir quitar el cortocircuito de TP2001 y TP2002.

Estos ajustes es necesario hacerlos cuando se sustituye los IC201, IC 2001, IC2002, IC3001 y el trc.

Cuando se sustituya e circuito integrado IC201 utilize el  Item: S26 (MTS).Si reemplaza el IC 2002 los valores iniciales están  en el IC2001.Cuando se sustituye el IC2001 los datos estan en el IC2002.Los valores S17, S19 y S22, su valor normal es: 0.El valor S5 debe fijarse en: 3.El valor S24 debe fijarse en: 32.

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Modo de servicio para Sharp 37Et-35S

Presionar simultaneamente,las teclas de volumen menos (V-) y programa mas (P+)

                                                                    SANYO

Presionar a la vez las tecla de memoria del mando a distancia,y la memoria(M)que se encuentra en el panel frontal de tvc.

Con el mando a distancia mantener presionada la tecla Menu del mando y pulsar el pulsador numero 2 del mando a distancia

Encender el TV. Pulsar la tecla Memoria del panel frontal de televisor aproximadamente 3 segundos .Seguidamente pulsar la tecla M del mando a distancia,y seguidamente la tecla Sonido(Sound),para ajustar con la tecla mas/menos del volumen,con la tecla sound seleccionamos los ajustes que queramos realizar.

                                                                   SONY

Con el televisor en Stand-by pulsar las teclas  del mando a distancia la siguiente secuencia I+ despues el numero 5 despues la tecla - (menos)de volumen y por ultimo la tecla pantalla,si hemos entrado en el modo de servicio nos saldra en la pantalla TT.Sigue las indicaciones en pantalla pulsando las teclas Menu y variando los parametros con las teclas roja y verde.Para salir del modo de servicio pulsar menu hasta que salga de nuevo TT y pulsar posteriormente dos veces 00.

Estando el TV desconectado del interruptor, presione el botón de servicio que se esta en la parte de atras del TV, en el modulo de conectores. Mantener  presionado mientras enciendes el TV con el mando a distancia. Con Audio y Video selecciona los menus. Con las teclas 1 y 4 elegir lo que queramos ajustar,  y con las teclas 3 y 6 ajustamos. Para memorizar los ajustes presionar Muting y despues Enter. Para salir del modo de servicio pulsar Power.

Estando el tvc en Stand-by, En el mando a distancia,presione las teclas (Display 5 Vol y Power on) o ( power off, Display,5 y power on). Con los teclas 1 y 4 elegimos los ajustes a realizarcon las teclas 3 y 6 ajustamos los valores. Para memorizar los ajustes presione las teclas Muting y  Enter,y para salir Power.

A continuacion una serie de codigos para probar si no logramos entrar con los 2 anteriores:                                                                                                                                            [PWR OFF] - [DISP], [5], [VOL+], [PWR ON] o [PWR OFF] - [DISP], [5], [PWR ON] o [PWR OFF] - [DISP], [5], [VOL+], [PICTURE], [PWR ON]

                                                              TOSHIBA

Mientras presionas el interruptor general de encendido presionas a la vez mute en el mando a distancia.de nuevo presiona otra vez mute pero manteniendo mas tiempo pulsada la tecla,mientras presionas mute presionas tambien TV en el frontal del televisor,despues suelta mute,entonces te saldra una S en la parte superior derecha en pantalla.Entonces  presionas Menu y ya estas en modo de servicio,con channel up y Down seleccionas el ajuste a cambiar,y con volumen up/down cambias los valores.

Estando el televisor conectado presionar dos veces Mute en el mando a distancia,en la segunda pulsacion debe de mantenerse presionada la tecla Menu,mientras simultaneamente presiona mute en el panel frontal del TVC,cuando nos aparezca S en la pantalla,otra vez pulsaremos Mute,con la tecla de programa,seleccionamos la funciona a ajustar,y con las teclas de volumen ajustamos los valores,

                                                              THOMSON

Estando el televisor conectado y funcionando,por el televisor en Stand-by con el mando a distancia,seguidamente apagas el televisor con el interruptor principal,ahora pulsas la tecla Azul del mando a distancia y conectas el interruptor pricipal hasta que te salga Setup,y ya estas en el modo se servicio de Thonson,ahora ten cuidado con la modificacion de valores,y realiza los ajustes con sumo cuidado.

Modos de Servicios extraidos de Internet

Marca

Modelo/Chasis

 Modos de Servicio y de Hotel

Repair Advice

NOKIA

Compact B-E2 Digital chassis

Service Mode

First Method - set with CCU11 uPC: press buttons from remote controls "mon-stereo" - "C" - "hypersonic" whithin 1 sec. Tha display shows "SE".

NOKIA

Compact B-E2 Digital chassis

Service Mode

First Method - set with CCU12 uPC: press the contact behind the small borehall on set front pannel (controls) and then button "S" whithin 5 sec. Tha display shows "SE".

PHILIPS

TV/VCR chassis

Hotel Mode

Activation
Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set.
De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec.. When de-activation is OK, a "H-" is displayed. To remove this display turn off-on the TV set.

PHILIPS

ANUBIS A chassis
2 local controls

Hotel Mode

First Method
Activation
Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" (or
"OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set. De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When de- activation is OK, a "H-" is displayed. To remove this display turn off-on the TV
set.'

PHILIPS

ANUBIS A chassis
2 local controls

Hotel Mode

Third Method
Activation
Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When activated "HOTEL
MODE" a green "H" is displayed. To remove this display turn off-on the TV set.
De-activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When de-activation is OK, a green "H" is displayed. To remove this display , turn off-on the TV set.

PHILIPS

ANUBIS A chassis
8 local controls

Hotel Mode

First Method
Activation
Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" (or
"OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set. De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When de- activation is OK, a "H-" is displayed. To remove this display turn off-on the TV
set.'

PHILIPS

ANUBIS A chassis
8 local controls

Hotel Mode

Second Method
Activation
Select program 38, then press simultaneously "INSTALL" and "PROGRAM+"
on local keyboard.
De-Activation Select program 38, then press simultaneously "INSTALL" and "CONTROL" on
local keyboard.

PHILIPS

ANUBIS A chassis
8 local controls

Hotel Mode

Third Method
Activation
Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When activated "HOTEL
MODE" a green "H" is displayed. To remove this display turn off-on the TV set.
De-activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When de-activation is OK,
a green "H" is displayed. To remove this display , turn off-on the TV set.

PHILIPS

G8 chassis

Hotel Mode

Activation
Select "Video2" mode. Press the remote control control keys "TELETEXT"
and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL
MODE" must be set "ON"
De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT"
and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL
MODE" must be set "OFF"

PHILIPS

G8.1ECO chassis

Hotel Mode

Activation
Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "ON"
De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "OFF"

PHILIPS

AA5 chassis

Hotel Mode

HOTEL MODE
Activation
Select program 38, press "MENU" on local keyboard and "SLEEPTIMER" (or
"OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off -on the TV set.
De-Activation
Select program 38, then press "MENU" on local keyboard and "SLEEPTIMER"
(or "OSD") on remote control for at least 4 sec.. When de-activation is OK, a
"H-" is displayed. To remove this display turn off -on the TV set.

PHILIPS

G8.1 chassis

Hotel Mode

Activation
Select "Video2" mode. Press the remote control control keys "TELETEXT"
and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL
MODE" must be set "ON"
De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT"
and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL
MODE" must be set "OFF"

PHILIPS

GR1-AX (8 buttons)

Hotel mode for models with uP TMP47C434N-R221

Select program 38 on the TV
Simultaneously press the STORE key on the TV and SLEEPTIMER on the remote for 4 about seconds (toggles hotel mode)
Notes:
The maximum volume in hotel mode will be the volume present when activating it
STORE or INSTALL mode can not be entered
The program number is displayed on the screen for 4 seconds
A green 'H' appears in the left bottom of the screen, which can be removed by powering down the TV and powering it up again

PHILIPS

ANUBIS A chassis
2 local controls

Hotel Mode

Second Method
Activation
Select program 38, then press simultaneously "INSTALL" and "PROGRAM+"
on local keyboard. De- Activation Select program 38, then press simultaneously "INSTALL" and "CONTROL" on
local keyboard.

PHILIPS

L6.1 (without Teletext)

Hotel mode

Select program 38 on the TV
Simultaneously press the - key on the keyboard of the TV and the OSD key of the remote control

PHILIPS

GR2.X

Service Mode

Short circuit pins M33 and M34 before powering up the TV. When powered up the TV LED will show as orange after which the short circuit can be removed. SER will be displayed on screen. Now press simultaneously keys INSTALL and PROG+ on the keyboard of the TV to activate the service menu

PHILIPS

GR1-AX (8 buttons)

Hotel mode for models with uP TMP47C434N-3414/3415, uP TMP47C634N-R494

Select program 38 on the TV
Simultaneously press the STORE key and the PROGRAM+ key on the TV for 4 about seconds (hotel mode on)
Simultaneously press the STORE key and the CONTROL- key on the TV for 4 about seconds (hotel mode off)
Notes:
The maximum volume in hotel mode will be the volume present when activating it
STORE or INSTALL mode can not be entered
The program number is displayed on the screen for 4 seconds

PHILIPS

ANUBIS B

Service Mode

Second method: With the TV powered off (disconnected from the mains!) short circuit pins M61 and M62 (next to IC7600). Power up the TV and remove the short circuit. A 'S' will be displayed indicating it is in service mode
Simultaneously press the P- and VOL+ keys on the TV. The screen now shows 'service menu'.
To allow hotel mode from being set on and off you have to select Option 2 with the remote and set 'Hotel' to 'on'.
Exit the service mode by putting the TV into standby

PHILIPS

ANUBIS B

Service Mode

First method: Select program 38 on the TV
Simultaneously press the P key and the VOLUME+ key (keyboard/remote)
To enable hotel mode you should set 'HO' to 'one'

PHILIPS

ANUBIS AA

Service Mode

Short circuit terminals M28 and M29 (IC7710)

PHILIPS

A10E chassis

Service Mode

This model also supports the 062596 sequence followed by [i+]/[OSD].
Service default mode is entered using the 062596 sequence, followed by the - button on the TV set itself.
Alternatively you can short-circuit pins 9261 and 9262 inside the set and then powering it up

PHILIPS

20PV220

Service Mode

TV preset 38
Push STOP -button on the remote and the PLAY -button on the TV simultaneously, for 5 seconds
You´ll get the service menu on screen
Clear EEPROM is the only cure for the problem that all items in installation menu are in ” non active ” mode with red text
Close TV from remote, and on again
Tune channels again

PHILIPS

21PT263A

Service Mode

Short circuit pin 1 of the EEPROM (24C08) to ground

PHILIPS

ANUBIS

Service Mode

Short circuit terminals M31 and M32 (IC7710)

PHILIPS

20PT424A

Service Mode

Short circuit pin 1 of the EEPROM (24C08) to ground

Schaub Lorentz

SL0014KO CTV-VCR

Service Mode

To enter SERVICE MODE, Unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and remote control key for more than 2 seconds. The both pressing of set key and remote control key will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 30 minutes before Power On or alternatively, discharge backup capacitor.

SCHNEIDER

TV8 chassis

Service Mode

Service-Mode
Before being switched to the service mode the unit must be set to a channel
with a test pattern. Note: The parameters are stored in changed.

Press the red key and the blue key on the remote control simultaneously. Within 5 seconds, press the key P-and the key V+ on the local control panel simultaneously

The title SERVICE Vxxx (xxx is for software version), appears in the screen.
Keys P+ and P- (program) Call up tuning parameters
Keys V+ and V- (volume) Modify tuning parameters

Display Operation
VP Adjust the vertical swift.
HP Adjust the horizontal swift.
VP Adjust the vertical picture height. Is the setting range not sufficient
the range must change with the point CRT.
VL Adjust top and button vertical linearity of screen centre.
VB Adjust the intensity of the EHT. VB=24
PA Make vertical lines parallel with screen edge.
HA Adjust the horizontal size.
CC Adjust vertical lines in corners. Basic setting is 0. Setting should only
be changed if PA balance cannot be adjusted satisfactorliy.
PT Adjust values so that picture has same with at top and bottom edges or
other vertical lines are parallel with each other.
R Colour drive adjustment
G Colour drive adjustment
B Colour drive adjustment
S-ADJ Connected a Test-picture with stereo signal to the tuner and adjust
the TV. Connected Oscilloscope to Pin of ST601. Adjust to lowest crostalk
between the channels.
L-ADJ Connect Oscilloscope to Pin 1 of ST601. Connect a Test-picture
(antenna level>60dBuV/75Ohm) with stereo signal (27kHz frequenceshift.54%
modulation factor) to the tuner and adjust the TV.
CRT Gear to vertical deflection. In dependence of the picture tube 0 or 1.
GR/G+GL Shows like the Cutoff registration locks of in place. Its useable
to adjust G2-adjustment.
DELAY Superimpose the luma signal on the chrominance signal.

Sharp

51DT25H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote control.

Sharp

4BS-C Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

51AT15H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode - 'SERV' appears on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off

Sharp

51CS05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

51DS02H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

51DS05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

59CS03H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

37AT25H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode - 'SERV' appears on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off

Sharp

51DS03H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

4BS-B Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

4BSA Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire To select an adjustment use the channel up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.

Sharp

37ET35H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote control.

Sharp

37EM33H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote control.

Sharp

37DT25H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote control.

Sharp

37AT25H

Cancel child lock

1 with tv switched off hold in both vol -- and prog + on tv 2 switch on tv it is now in service mode 3 use channel + to scroll through menu and stop at n v m (non volatile memory)
4 there will also be a 2 digit number in red on the screen as well as another 2 digit number in green, using the vol + button and at the same time observe the green display change the green number until C5 appears 5 At this point the red display shold show 00 for lock to be of
if it shows 01 change to 00 using 0 button 6 switch off the set
ps the menu is available for many adjustments take care !!!

Sharp

66CS05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

37AM23H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode - 'SERV' appears on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off

Sharp

37AM23H

Child Lock removal - pin no not known

PRESS VOL - ON TV & CHILD LOCK ON REMOTE TOGETHER , PRESS MODE ON REM, USING CHANNEL +/- TO SELECT CHILD LOCK , SELECT NEW PIN PRESS MODE E

Sharp

37AM12H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode - 'SERV' appears on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off

Sharp

59CS05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

37DM23H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote control.

Sharp

DV5135H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just like a passing contact switch
5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

59CSD8H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DV6640H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

66AS06H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

DV6635H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

DV66083H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode

Sharp

DV6603H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode

Sharp

DV5105H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just like a passing contact switch
5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

DV5107H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just like a passing contact switch
5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

DV5940H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

DV5131H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DV3751H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DV5150H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DV5161H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire To select an adjustment use the channel up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.

Sharp

DV5165H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DV5180H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DV5903H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode

Sharp

DV59083H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode

Sharp

DV5932H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

DV5935H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

DV5937H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

DV51083H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode

Sharp

66ES05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

59DS03H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

59DS05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

59ES03H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

59ES05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

59ESD7H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

5BSA Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode - 'SERV' appears on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off

Sharp

66AS05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

66CS03H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

66DS03H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

66DW18H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DV3760H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire To select an adjustment use the channel up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.

Sharp

66ESD7H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

76DW18H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

BCTVA Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

D3000 Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode

Sharp

CW100 Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DECO-4 Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just like a passing contact switch
5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

Deco-5 Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just like a passing contact switch
5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

Sharp

S3B Chassis

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

Sharp

DV3770H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire To select an adjustment use the channel up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.

Sharp

66DS05H

Service Mode

1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

SIEMENS

FM550.XX chassis

Emergency Data

The processor IC850 in this TV receiver is fitted with two memories in which the picture
geometry data are stored. If this IC fails or the data have been changed, the TV receiver must be switched on the emergency data set. Emergency Data Loading the Emergency Data :Press and hold the "P-"button on the local keyboard and switch the TV on with the mains button. In doing so, the data sets for the picture geometry values, the deflection and chrominance data are loaded from the keyboard control unit into the respective modules. Subsequently, call up the Info Center
Menu - Special Functions - Service - Code Number 8500 - Geometry and change the
setting if requested. To store the data Call up "end without mem." and select "End with
mem." using the buttons < or >. Initialisiation of the uP (IC8500) (eg. After changing the uP IC 850) - Connect Pin 1 of the processor to chassis and switch the TV on with the mains switch to load the EEPROM in the processor IC850

SONY

KV27S45

ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER"
To WRITE TO EEPROM "Press" - "MUTING" - "ENTER"
To INITIALIZE EEPROM "Press" "8" - "ENTER"

ID-0 153, ID-1 27, ID-2 13, ID-3 195, ID-4 31, ID-5 1, ID-6 1, ID-7 64

SONY

KV32S25

ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER"
To WRITE TO EEPROM "Press" - "MUTING" - "ENTER"
To INITIALIZE EEPROM "Press" "8" - "ENTER"

ID-0 25, ID-1 21, ID-2 31, ID-3 0, ID-4 27, ID-5 0, ID-6 1, ID-7 0

SONY

KV32XBR85

ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER"
To WRITE TO EEPROM "Press" - "MUTING" - "ENTER"
To INITIALIZE EEPROM "Press" "8" - "ENTER"

ID-0 120, ID-1 127, ID-2 126, ID-3 52, ID-4 28, ID-5 NA, ID-6 NA, ID-7 NA

SONY

KV32V16

ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER"
To WRITE TO EEPROM "Press" - "MUTING" - "ENTER"
To INITIALIZE EEPROM "Press" "8" - "ENTER"

ID-0 120, ID-1 127, ID-2 72, ID-3 36, ID-4 19, ID-5 NA, ID-6 NA, ID-7 NA

SONY

KV32V65

ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER"
To WRITE TO EEPROM "Press" - "MUTING" - "ENTER"
To INITIALIZE EEPROM "Press" "8" - "ENTER"

ID-0 89, ID-1 55, ID-2 175, ID-3 10, ID-4 27, ID-5 141, ID-6 6, ID-7 0

VESTEL

11AK20S CHASSIS

Service Mode

How to enter and exit the SERVICE Menu:
Enter the Main Menu
Press the digits 4, 7, 2, and 5, respectively
Press MENU key to exit
There're two selections in the Service Menu: "ADJUST…" and "OPTIONS…" ADJUST Menu: Move the selection bar on the item "ADJUST…" using the P+ or P- keys,
Select the item "ADJUST…" using the < or > keys,
The items below will be displayed (one of them at one time),
1) AGC (Automatic Gain Control) 8) HSH (Horizontal Shift)
2) VA1 (Vertical Amplitude for 4:3, 50Hz) 9) WG (White Point GREEN)
3) VA2 (Vertical Amplitude for 16:9, 50Hz) 10) WR (White Point RED)
4) VA3 (Vertical Amplitude for 4:3, 60Hz) 11) WB (White Point BLUE)
5) VA4 (Vertical Amplitude for 16:9, 60Hz) 12) CR (Cut-off Red)
6) VSH (Vertical Shift) 13) CG (Cut-off Green)
7) VL (Vertical Linearity) 14) OSH (OSD Horizontal Position)